|
ACOUSTICAL1
|
|
Operating Frequency Range2
|
55 Hz – 18 kHz
|
|
Phase Response
|
92 Hz – 18 kHz ±30 degrees
|
|
Linear Peak SPL3
|
133.5 dB with 18 dB crest factor (M-noise), 130 dB (Pink noise), 134.5 dB (B‑noise)
|
|
COVERAGE
|
|
Horizontal Coverage
|
110°
|
|
Vertical Coverage
|
Varies, depending on array length and configuration
|
|
TRANSDUCERS
|
|
Low Frequency
|
Two 9‑inch long‑excursion cone drivers; 2 Ω nominal impedance
|
|
High Frequency
|
One 3‑inch diaphragm compression driver coupled to a constant‑directivity horn through a patented REM® manifold; 4 Ω nominal impedance
|
|
AUDIO I NPUT
|
|
Type
|
Differential, electronically balanced
|
|
Maximum Common Mode Range
|
±15 V DC, clamped to earth for voltage transient protection
|
|
Connectors
|
XLR 5‑pin female input with male loop output; XLR 3‑pin female connectors available to accommodate only balanced audio (no RMS signals)
|
|
Input Impedance
|
10 kΩ differential between pins 2 and 3
|
|
Wiring4
|
Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamped network to provide virtual ground lift at audio frequencies
Pin 2: Signal + Pin 3: Signal ‑
Pin 4: RMS (polarity insensitive) Pin 5: RMS (polarity insensitive) Case: Earth ground and chassis
|
|
Nominal Input Sensitivity
|
6.0 dBV (2.0 V rms) continuous is typically the onset of limiting for noise and music
|
|
Input Levels
|
Audio source must be capable of producing +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
|
|
AMPLIFIERS
|
|
Type
|
3‑channel, open‑loop, class D
|
|
Total Output Power5
|
3900 W peak
|
|
THD, IM, TIM
|
<0.02%
|
|
Cooling
|
Convection
|
|
AC POWER
|
|
Connector
|
powerCON 20 input with loop output
|
|
Automatic Voltage Selection
|
90–265 V AC
|
|
Safety Rated Voltage Range
|
100–240 V AC, 50–60 Hz
|
|
Turn‑on and Turn‑off Points
|
90 V AC turn‑on, no turn‑off; internal fuse‑protection above 265 V AC
|
|
CURRENT DRAW
|
|
Idle Current
|
0.46 A rms (115 V AC); 0.35 A rms (230 V AC); 0.49 A rms (100 V AC)
|
|
Max Long‑Term Continuous Current (>10 sec)
|
3.0 A rms (115 V AC); 1.5 A rms (230 V AC); 3.4 A rms (100 V AC)
|
|
Burst Current (<1 sec)6
|
4.4 A rms (115 V AC); 2.3 A rms (230 V AC) 5.5 A rms (100 V AC)
|
|
Maximum Instantaneous Peak Current
|
12.6 A peak (115 V AC); 6.3 A peak (230 V AC); 14.5 A peak (100 V AC)
|
|
Inrush Current
|
<20 A peak
|