|
ACOUSTICAL1
|
|
Operating Frequency Range2
|
55 Hz – 18 kHz
|
|
Frequency Response3
|
57 Hz – 18 kHz ±4 dB
|
|
Phase Response
|
80 Hz – 18 kHz ±45°
|
|
Linear Peak SPL4
|
135 dB with crest factor >17 dB (M-noise), 132 dB (Pink noise), 134 dB (B‑noise)
|
|
COVERAGE
|
|
|
80° horizontal x 80° vertical (‑6 dB)
100° horizontal x 100° vertical (‑10 dB)
|
|
TRANSDUCERS
|
|
Low Frequency
|
One high‑power 15‑inch cone driver with neodymium magnet; 2 Ω nominal impedance
|
|
High Frequency
|
One 4‑inch diaphragm compression driver; 8 Ω nominal impedance
|
|
AUDIO INPUT
|
|
Type
|
Differential, electronically balanced
|
|
Maximum Common Mode Range
|
±15 V DC, clamped to earth for voltage transient protection
|
|
Connectors
|
XLR 3‑pin female input with male loop output; optional 5‑pin connectors to accommodate both balanced audio and RMS signals
|
|
Input Impedance
|
10 kΩ differential between pins 2 and 3
|
|
Wiring
|
Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal + Pin 3: Signal ‑
Case: Earth ground and chassis
|
|
Nominal Input Sensitivity
|
0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
|
|
Input Level
|
Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
|
|
AMPLIFIER
|
|
Type
|
Two‑channel, Class‑D
|
|
Total Output Power5
|
2250 W peak
|
|
THD, IM, TIM
|
< 0.02%
|
|
Cooling
|
Convection
|
|
AC POWER
|
|
Connector
|
PowerCON 20 input with loop output
|
|
Automatic Voltage Selection
|
90–265 V AC, 50–60 Hz
|
|
Safety Agency Rated Voltage Range
|
100–240 V AC, 50–60 Hz
|
|
Turn‑on and Turn‑off Points
|
90 V AC turn‑on; no turn‑off; internal fuse‑protection above 265 V AC
|
|
CURRENT DRAW
|
|
Idle Current
|
0.27 A rms (115 V AC); 0.25 A rms (230 V AC); 0.29 A rms (100 V AC)
|
|
Maximum Long‑Term Continuous Current (>10 sec)
|
2.0 A rms (115 V AC); 1.0 A rms (230 V AC); 2.3 A rms (100 V AC)
|
|
Burst Current (<1 sec)6
|
3.8 A rms (115 V AC); 1.9 A rms (230 V AC); 4.4 A rms (100 V AC)
|
|
Maximum Instantaneous Peak Current
|
8.4 A pk (115 V AC); 4.1 A pk (230 V AC); 9.7 A pk (100 V AC)
|
|
Inrush Current
|
< 20 A peak
|
|
RMS NETWORK (OPTIONAL)
|
|
|
Equipped with two‑conductor twisted‑pair network, reporting all operating parameters of amplifiers to system operator’s host computer.
|